Looking to upgrade the rear end of your beloved Jeep Wrangler?
Look no further!
In this guide, we’ll walk you through the simple yet essential steps to install a back window on your Jeep Wrangler.
Get ready to revamp your ride and cruise in style with a crystal-clear view of the road behind you.
Let’s dive in!
how to install back window on jeep wrangler
To install a back window on a Jeep Wrangler, start by removing the tailgate.
Then, remove the old window by unzipping it or removing any screws or clips holding it in place.
Clean the window frame thoroughly.
Align the new window with the frame and secure it using clips, screws, or zippers.
Test the window to ensure it opens and closes properly.
Reattach the tailgate and reconnect the rear wiper electrical and washer hose.
Lastly, bolt the hinges to the hardtop and connect the wiring and washer connection.
- Remove the tailgate before installing the back window.
- Take out the old window by unzipping or removing screws/clips.
- Clean the window frame thoroughly.
- Align and secure the new window with clips, screws, or zippers.
- Test the window to ensure proper opening and closing.
- Reattach the tailgate and reconnect the rear wiper electrical and washer hose.
Check this out:
💡 Did You Know?
1. The first Jeep Wrangler with a removable back window was introduced in 1997 as part of the TJ generation, allowing for increased versatility and easy access to the cargo area.
2. Prior to the introduction of removable back windows, Jeep Wrangler models featured a fixed back window that had to be replaced in its entirety in case of damage.
3. The process of installing a back window on a Jeep Wrangler generally involves removing the existing window by unzipping or unclasping it from the surrounding fabric, cleaning and preparing the area, and then attaching the new window using zippers or clips.
4. While the installation process may seem straightforward, it is important to note that improper installation of a back window on a Jeep Wrangler can result in leaks, wind noise, or even damage to the window itself.
5. There are a variety of aftermarket options available for Jeep Wrangler back windows, including tinted windows for added privacy and protection against UV rays, as well as windows with built-in heating elements to prevent fogging and facilitate easier visibility.
Remove The Old Back Window
Removing the old back window is the first step in installing a new one on your Jeep Wrangler. To begin, you will need to remove the tailgate. This can typically be done by detaching any bolts or clips securing it in place. Once the tailgate is removed, you can proceed to remove the old window.
To remove the old window, unzip it from the existing frame if it is a zippered window. If the window is held in place by screws or clips, carefully remove them to release the old window. Take caution to avoid damaging the glass during this process.
Prepare The Window Frame
Before installing the new window, it is crucial to clean the window frame thoroughly. Use a mild cleaner to remove any dirt, debris, or residue from the frame. This step is important in ensuring proper adhesion for the new window.
Take your time and pay attention to detail when cleaning the window frame. Any leftover dirt or residue can compromise the installation and result in a poor fitment.
Install The New Window
Once the window frame is clean and prepped, it is time to install the new back window. Start by aligning the new window with the frame, carefully ensuring a secure fit. It may be helpful to have a friend assist you in holding the window to prevent it from shattering.
With proper alignment, insert the new window into the frame. Ensure that the window sits flush and is centered within the frame. Take your time to make any necessary adjustments before proceeding to the next step.
Secure The Window To The Frame
To secure the new window to the frame of your Jeep Wrangler, use the appropriate clips, screws, or zippers provided. These components may vary depending on the window manufacturer and specific Jeep Wrangler model. Refer to the instructions provided with your new window to ensure a proper and secure attachment.
Carefully follow the provided instructions, ensuring that the window is securely fastened to the frame. Pay attention to any torque specifications or specific installation steps outlined by the manufacturer.
Test The Window Functionality
Once the window is properly secured, it is essential to test its functionality. Open and close the window to ensure smooth operation. Check for any signs of resistance or misalignment. If any issues are encountered, double-check the installation and make any necessary adjustments.
A smoothly functioning window is vital for enjoying an optimal driving experience and ensuring the window’s longevity. Take the time to thoroughly test the window before finalizing the installation.
- Open and close the window to test functionality
- Check for resistance or misalignment
- Double-check installation for any necessary adjustments
“A smoothly functioning window is vital for enjoying an optimal driving experience and ensuring the window’s longevity.”
Reattach The Tailgate
After confirming the proper functionality of the new window, reattach the tailgate to complete the installation.
- Reinstall any bolts or clips that were removed earlier to secure the tailgate in place.
Ensure that the tailgate is aligned correctly and closes properly.
- Check for any gaps or misalignments that may have resulted from the installation process.
- Adjust if necessary to achieve a seamless fit.
Disconnect Rear Wiper And Washer Hose
To proceed with the installation, there are two important steps to follow:
- Disconnect the rear wiper electrical connections and washer hose (if applicable):
- Refer to the manufacturer’s instructions or consult the vehicle’s manual for specific guidance on disconnecting these components.
Take care to follow the provided instructions to avoid any potential damage.
Ensure proper disconnection:
- Make sure that all connections are properly disconnected.
- Take notes or pictures if needed to assist in reconnection later.
- It is crucial to avoid any damage to the electrical wires or hoses during this process.
By carefully following these steps, you can proceed with the installation smoothly and without causing any harm to the electrical components or hoses.
Bolt The Hinges And Reconnect Wiring
At this stage, you can proceed to bolt the hinges back onto the hardtop. There are typically four bolts, two on each hinge, located on the back of the hardtop. Carefully tighten the bolts to ensure a secure attachment.
Once the hinges are tightened, reconnect the wiring and reattach the washer connection, if applicable. Take your time to ensure that all connections are properly reconnected, double-checking for any loose or improperly fitted components.
Following these steps will guide you through the process of installing a back window on your Jeep Wrangler. It is essential to refer to the specific manual or instructions provided by the window manufacturer for your particular model to ensure proper installation. With attention to detail and patience, you can successfully upgrade the back window of your Jeep Wrangler.
- Bolt the hinges back onto the hardtop
- Tighten the bolts to ensure a secure attachment
- Reconnect the wiring
- Reattach the washer connection, if applicable
It is essential to refer to the specific manual or instructions provided by the window manufacturer for your particular model to ensure proper installation.
Can you install power windows on a Jeep Wrangler?
Yes, power windows can indeed be installed on a Jeep Wrangler using a specific kit designed for this purpose. The kit includes the necessary components such as a dash-mounted switch panel, individual switches for the rear doors, motor mounting plates, and detailed installation instructions. With step-by-step instructions provided, even those with minimal mechanical experience can successfully complete the installation and achieve professional results. Transforming your Jeep Wrangler with the convenience of power windows is made accessible through this comprehensive kit.
Why wont my jeep rear window go up?
If your Jeep Wrangler’s rear window won’t go up, it could be due to a variety of issues within the electrical system. Start by checking the fuse and relay associated with the window, as a blown fuse or faulty relay might be the culprit. Additionally, a broken window motor could be preventing the window from functioning correctly. Finally, it’s also possible that the window regulator, which controls the movement of the window, is broken and needs to be replaced. By examining these components, you should be able to diagnose and resolve the issue with your Jeep’s rear window.
Can you install power windows?
Yes, absolutely! With the help of a power window kit, you can easily upgrade your car’s manual windows to power windows. These kits come with all the essential components like motors, switches, and wiring to make the installation process smoother. By converting your windows to power windows, you can enjoy the convenience and ease of effortlessly operating them with just a touch of a button. It’s a great way to enhance your car’s functionality and modernize its features.
Is it possible to install power windows in a car?
Yes, it is possible to install power windows in a car. Unlike trucks, cars have a spacious cavity behind the door panel, eliminating the need for cutting away any metal to accommodate switches and wiring harnesses. This makes the conversion process relatively easier and more straightforward. By installing power windows, you can enjoy the convenience and ease of operating the windows with a simple press of a button, enhancing the overall comfort and functionality of your car.